Home

Refrigerator Door Handle Repair

The point at which the door handle attaches to the refrigerator is usually well-hidden, building a repair seem more complicated than it really is. Should you inspect the manage carefully, however, you can usually locate the screws which hold it in place or at least the panel which covers the screws.

Screws and Tracks

Inspect the manage to discover the attachment point. If you’re able to see the screws, use an Allen wrench or screwdriver to tighten the screws to repair a loose manage, or remove them and replace a cracked handle. When the screws are hidden, try sliding the handle up or to the lefthand. Do not put so much pressure that it will damage or break the grip, but use enough to determine whether it slides away on a track or is attached by screws. Slide off the handle if it is not screwed on, and tighten the screws on the tracks, or remove the whole assembly if you’re replacing the grip. To get a handle attached by screws, look for a tiny removable panel. The panel might slide out of the way or you might want to gently pry it away. Remove the panel and tighten the screws, or loosen them to remove the handle.

Home

The way to Caulk the Cracks in the Walls of a Fireplace

The sides and back wall of a standard wood-burning fireplace are built using fire bricks and mortar. Over time, excessive heat can adversely impact cement, causing the joints to crack or flake. In the event you become aware of bits of mortar on the ground Flagstaff of a fireplace, flattening the cracks employing a silicate-based refractory cement caulking that disables heat. Preparation is the trick to effectively caulking the cracks in a fireplace.

Wear work gloves, a dust mask and safety glasses. Protect the hearth and adjacent flooring or carpeting, using a drop cloth. Open the fireplace display completely and eliminate the log grate from the fireplace.

Eliminate debris and ash from the floor of the fireplace, employing a wet-dry vacuum. Eliminate soot from the mortar joints in the sides and rear walls of the fireplace, employing a stiff-bristle brush.

Inspect the vertical and horizontal mortar joints for cracks or flaking. Eliminate loose mortar at these regions, employing a 3-inch cold chisel and hammer. Use the brush to remove any remaining brick from the subjects of repair. Clean the debris up with the vacuum.

Set up a caulking gun with a tubing of silicate-based refractory cement caulking. Cut off the tip of the tubing to make a 1/8-inch opening, using a utility knife.

Caulk the ready areas in the mortar. For your best results, use a continuous motion as you draw the tip of the tubing along a crack. You might have to use a number of layers to get wider cracks. Permit the caulking to dry before using the fireplace.

Home

Residential Garage Building Material Lists

Garage plans and layouts are incomplete without a list of substances for the undertaking. The substances list is essential for preparation, ordering and organization. The standard building method to get a residential garage starts with balloon framing, additionally referred to as stick-built by most carpenters. To determine the materials needed, begin with the building’s measurements, framed 16 inches on center. Local building codes define nailing patterns, which will allow you to calculate the number of nails and other special conditions for your project. Start with an accurate materials list and your garage project — even in the event that you’ve contracted it — will go smoothly and without any surprises.

Ground Flagstaff Floor

Concrete starts the substances list off, sized by the garage dimension and a typical 4-inch slab. But before concrete is poured, residential garages usually require rebar or steel mesh integrated to the mat. Many building jurisdictions additionally call to get a plastic vapor barrier beneath the concrete depending on particular soil types. If you plan stem walls in your garage so that you can wash it out with a hose, include the sum of concrete brick needed for a single class around the perimeter of the garage and the bolts that fasten the only plate to them for framing.

Framing the Garage

The vast majority of wall framing entails two-by-four studs, and a few two-by-sixes, as needed. Depending about the wall height, the studs can vary from 96-inches to 120-inches or more. Along with studs, don’t forget base or only plates and top plates to secure the studs to create the walls. If you plan doors and windows for the garage, then include two-by-twelve headers over doors and windows. However, for the main overhead metal garage door, check local code requirements, as this header generally has to be an engineered laminated beam that can span the space. Do not forget to add metal earthquake straps, drywall, batt insulation, wiring, outlets and lighting fixtures to get a finished garage.

Exterior Sheathing

Exterior wall sheathing made from 5/8-inch thick, 4-by-8 feet sheets of oriented strand board follows next, covered with some sort of vapor barrier such as sheathing paper or polyethylene plastic. For soffits and fascia, include 3/4-inch cedar and vented aluminum displays on the record. When planning your garage door, match its outside to your home’s exterior, such as stucco, vinyl or wood — shiplap or tongue and groove — siding, amounts calculated according to the garage measurements.

Over the Head

Prebuilt engineered roof trusses work best to the roof support. Framed roof trusses — triangular shaped for the roof pitch — utilize two-by-four lumber secured at joints using metal plates. Frame-style trusses sit far nearer together on the outside walls, requiring more time to set up. It is possible to build trusses on website but prebuilt engineered trusses have greater strength and integrity in comparison to site-built trusses. Prebuilt engineered trusses demand a boom truck or binder to lift them atop the walls and to stabilize them during setup, usually supplied by the business who made the trusses. Add plywood roof decking, felt or tar paper, caulk, seams or corrugated metal to the record to fill out the roof.

Fasteners and Other Things

The two most frequent sizes of nails are 8d and 16d covered sinker nails. Use these for the bulk of the framing. Roofing nails are also vital. Depending on roof type that they vary from 1-to-1 1/2-inches in span. Purchase nails in 25-pound mass sizes to conserve money. An assortment of flashing can also be needed to seal joints across the roof, doors and windows. Flashing consists of hexagonal strips of metal to deter water penetration. Other weather-related items comprise caulking, paint and gutters.

Home

Tar Roof Repair

Tar roofs generally require replacing as opposed to repairs, because most do-it-yourself patches are just temporary fixes that will endure for a few months, as opposed to a decade. A temporary repair may get you time to prepare financially for a new roof or to employ a specialist with the required equipment to complete a longer-lasting repair. A temporary fix is also preferable to enabling water to damage the roof.

Burst the Bubble

The area where damage has occurred on a tar roof bubbles up or lifts away from the roof. There may nevertheless be water puddled on top of the damaged area. The first step is to sweep the water away, remove the gravel and set it aside, then open the bubbled area with a utility knife or razor blade by cutting an “X” across the center.

Wash and Dry

Lift the flaps of this “X” up so that air may circulate to the bottom layers. Wipe away as much moisture and dirt as possible. Allow the damaged region air dry until all the moisture is eliminated. Wash any remaining dirt or debris from the region. The patch will not stick to a surface that is moist. It adheres better to a tidy roof which isn’t covered in a layer of dirt.

Building Layers

Spread a layer of tar on the roof beneath the spot you have cut away. Press the flaps from the cut portion into the tar and subsequently spread another layer of tar on top of the flaps. Push the tar from this layer out a bit farther so that it goes about six inches past the ends of the cut. Then press a sheet of cotton fabric into the nest till it’s completely saturated with pitch. Add another layer of tar and distribute it out past the edges of the fabric.

Finishing Touches

Feather the edges of the tar nicely past the ends of the fabric, smoothing it out so that it blends with and adheres to the surrounding tar surface. Eliminate additional gravel is necessary and set it aside to add tar as required. Gently replace the gravel by hand, taking care to cover every area of the patch. Do not use tools to push back the gravel into place, as you could loosen the patch. When working on a roof function safely, put on a hat to protect against sun exposure and wear a safety harness, if necessary, to protect against drops.

Home

Luxury Pool Renovation Ideas

Renovation adds even more enjoyment to a luxury pool, enhancing its relaxing vibe or adding otherworldly hues through use of tiles or lighting. Create your mini ecosystem around the pool using the addition of plants and landscaping San Diego, CA, or even flip it into a home-based water park using tunnels and slides. If you can imagine it, then there is a chance it can be built with a skilled pool-building company.

Swimming and Spelunking

Turn the pool right into a mysterious cave-riddled area ready for exploration by adding large synthetic boulders and cave-like enclosures lit with ambient lighting. If space permits, some caves might require swimming through a shallow tube or even faux mine entrance to reach the internal alcove. A spa carved out of synthetic stone, under an overhang produces a cave-like feeling with its hot spring. Insert art inspired by cave drawings to the cave walls for a prehistoric touch. Carve measures and walkways up the synthetic boulders over the cave for a place to relax; a built-in slide or an added diving board contributes to the water.

Personal Water Park

Turn your pool place into a personal water park for old and young alike by adding a series of diving boards for the deep end, swinging ropes to jump out of and side-by-side slides for racing into the water. Goal nets decorate superficial finishes of the pool for a busy game of water polo, or establish a net round the pool for water volleyball. A fountain in the center of the pool functions as decor when maintaining those from the water extra cool.

A Bit of Paradise

Turn the pool and poolside areas into a tropical paradise with potted palms, tropical plants and an infinity pool with a view. Insert an in-ground spa near the pool area, tucked away into its very own private grotto for individual comfort space. Waterfalls emanating from one level to the next add layers to the swimmable spaces. Stone tiles cover the deck area around the pool, while speakers at the pool or put strategically outdoors pump your favorite music over place. Water temperature controls are instantly accessible to tailor the environment to your tastes each day.

Adding Ambiance

Sometimes, the small things can kick the pool ambience up a notch. Indigo glass or glass tiles decorate the pool walls or parts of them, or go all-out using a mosaic layout on the bottom of the pool, either such as a treble clef for a music lover, or also a series of tropical fish or dolphins. Ambient lighting mounted at the pool wall produces an after-dark swim a fun, relaxing experience, providing enough light to swim by without being overly bright. Color-changing LED lighting tints the water any hues desired. Outdoor lighting adjusts to the right amounts for ambiance.

Home

The way to Eliminate an Aluminum Porch Awning

When an present aluminum porch awning no longer suits your personality along with the decor of the home, it is time to carry it down. Removing this shade-providing structure typically does not demand a professional’s aid, but it will demand a thorough inspection first — perhaps not all awnings are made evenly, so it is important to figure out how yours was installed so you’re able to remove it successfully. A metallic awning is also quite heavy. Enlist a few friends to help support the awning as you remove it, to prevent it from crashing into the ground Cape Coral.

Examine the bottom of the awning, looking especially at the framework holding the structure onto the building. Typically, steel support mounts or arms hold the masonry slats or roof; it is the support mounts or arms that attach into the home.

Prop a board up on either side of the awning, under it for example articles, to support the awning’s weight if it is heavy. Whack the boards with a mallet to push up them as straight as possible.

Remove the screws from the awning support brackets, arms or braces attached to the building, using a screwdriver. Stand so that you aren’t directly under the awning, and that means you’re protected if it starts to sag on one side. Ask a friend to help maintain the outside portion of the awning on the side you’re working on. A ladder may be necessary.

Remove the screws from hold brackets on the other side of this awning while the other friend helps maintain the awning on this side one friend is on each side.

Gently guide the awning to the ground Chico, using the leverage of the boards to help keep the awning from crashing straight down.

Home

The way to Troubleshoot a GEW9250PW0 Duet Dryer

Whirlpool’s model amount GEW9259PW0 Duet Dryer — an electric prototype which goes straight back to 2005 — comes equipped with features like the crease-preventing wrinkle shield fluffing cycle and a drying rack for stationary, nontumble drying. Distinct attributes apart, the GEW9259PW0 is a straightforward machine which calls for straightforward troubleshooting procedures when it doesn’t function effortlessly.

Think Easy

Before pursuing more complex troubleshooting steps, check your fuse box for a blown fuse — that dryer in particular needs two time-delay fuses — or a tripped circuit breaker as soon as your Duet GEW9259PW0 fails to get started. In case your Duet dryer won’t begin when packaged with a particularly large load, press and hold the “Start” button for 2 to 5 seconds. If the drier’s screen indicates the error code “PF,” it might cease during surgery. This implies a temporary power failure has interrupted the drying cycle; press and hold “Start” to restart the dryer.

Encourage Air Flow

Without proper air flow, you might find that your Duet’s drying power reduced. Lint functions as a frequent inhibitor of atmosphere flow, so wash your Duet’s lint display prior to every use. Whirlpool recommends running the heat display under warm water and scrubbing it with a nylon brush and a bit of liquid detergent at least every six months. If you do not feel air coming in your GEW9259PW0’s exhaust hood after 5 to 10 minutes of operation, clear the exhaust system of lint. Likewise, ensure that no fabric softener sheets block the appliance’s grille — restrict yourself to one fabric softener sheet per load to prevent this possible blockage issue.

Identify Other Issues

In case your Duet’s drum doesn’t move as it needs to, inspect the borders of this drum for small objects — like pocket change or paperclips — lodged between the drum and the frame and remove any obstacles. To remedy extra vibration and noise, guarantee that the cutting legs included with your dryer are properly installed. Expand these legs to the drier’s leg holes by hand, turning them till the diamond-shaped marking is no longer visible. Keep the area around the Duet dryer sufficiently warm, as Whirlpool notes which appropriate operation requires temperatures over 45 degrees Fahrenheit.

Reach Out

If your dryer fails to heat, a high-temperature switch or the heater component might be blown. In case you have appliance repair experience, you can replace those items yourself, otherwise you need professional aid. For instance, if your Duet dryer displays any variable of this “E” service code — like “E1,” “E2” or “E3” — contact a repair professional or Whirlpool directly. Locate your version number on the inside rim of the dryer door prior to making the phone.

Home

The Gas Dryer Is Making Loud Clunking Noises and Is Not Drying

Dryers might appear big, intimidating and bulky, but as far as appliances move, they’re the darlings of do-it-yourselfers. You can solve many gas dryer problems by straightforward troubleshooting, and dryer parts are not that hard to access or replace. If you notice a combination of clunking noises and not drying, however, the scenario doesn’t possess a single solution. You’ll have to play detective, because at least two things are wrong with your dryer.

Start Simple

Naturally, your dryer is plugged in — right? — but don’t double check that it is, since this is a potential reason for clothing not drying. Then assess the lint filter and then the port opening to the outside. Brush away all the lint, and make it a habit to remove lint before and after each drying cycle. Another obvious but possible problem: Make sure the dryer is set to a heated cycle; you also could accidentally be on Fluff Air or also a similar choice on the dial.

Broken Rollers

Broken rollers lead the record of suspects causing clunking noises. Two rollers, one each in the right and left sides below the drum, support the drum as the belt turns it. A set place in the rubber or a broken piece may cause a quick clunking sound, which amplifies to a resounding din that thumps all through the house. It is possible to open the front panel of your dryer, pull the drum and replace the rollers.

Additional Reasons for Clunking Noises

A marginally slower clunking noise may be in the metal-to-metal scraping of worn dryer drum glides. Or the belt may be worn, or the clothing baffle loose. If you observe clunking with nothing at the drum, you might have foreign objects in the blower wheel. Checking this option requires disassembling the dryer to access this massive plastic wheel adjacent to the port, typically in the lower left rear of the dryer when facing the rear panel. You can consult online resources that perform sample sounds of their different clunking noises, which conveniently inform which noise goes with which problem. If you can’t otherwise explain the noise, the problem might be with the engine and will require a professional technician.

Trickier Reasons for Not Drying

Once you’ve eliminated the basic reasons for clothing not drying, escalate your investigation to the thermal fuse for continuity, which you may check using a multimeter. If the fuse checks out, then test the thermostat or thermostats, again using a multimeter. If the thermal hoist and also thermostats test OK, the problem may lie together with the gasoline burner assembly and will require a trained technician.

Home

How to Adjust Bed Skirts for Cribs

Babies do not need crib skirts, but their doting parents and grandparents are partial to them. The confounding thing about having a crib skirt is that when you lower the mattress so the growing small monkey can not climb out, the crib skirt sags all over the ground Flagstaff. Preserve your cautious nursery decor, and your sleep-deprived sanity, by building in a simple adjustable feature to this tailored, ruffled, gathered, what-was-I-thinking piece of fabric icing ringing the bottom of the crib.

Removable Ruffle

Ruffled crib skirts announce a party — and a great deal of work. You want to have that combined match-up of endlessly gathered patterns and colors to be only perfect, a scenario with no room to your bottom ruffle dragging on the ground by the princess’s very first birthday. While you’re carefully assembling your crib-skirt confection, run a line of sticky hook-and-loop binding across the top of the final ruffle as well as the bottom edge of the capital to that the ruffles are sewn. Stick the bottom ruffle into the backing. The newborn gets the deep ruffle therapy; the toddler gets the short version using the bottom ruffle removed.

Short and Sweet

No rule exists mandating a crib skirt that dusts the ground Flagstaff. So start out in which you plan to find yourself. Begin with a pretty crib skirt that is about 6 inches shy of the ground San Diego. When you decrease your mattress — sooner than you believe you will — the skirt will skim the carpeting. If you do not want to have the crib skirt to evaporate because of its brief, shorter incarnation, use a daring color — lime in a turquoise and cream nursery — or also a wild pattern such as animation rain forest creatures in tropical hues in an apricot or mint green nursery.

Tacked Up

The no-fuss school of nursery decor is happy to be sticky. Cut and hem separate bed skirt panels for each exposed side of the crib. If your crib sits against a wall, you can skip the skirt for this side. Tack each panel into the support stage below the crib mattress so the skirt only dusts the ground Miami. When you decrease the mattress, remove the tacks and adjust the distance of the panels prior to re-tacking.

Easy Pieces

Cut two decks the apartment, never-seen article of fabric that sits on the mattress support panel below the mattress. Crib skirts are sewn into the deck, which holds the visible panels of the skirt in place. Stitch the key decorative crib skirt to a single deck — a nautical nursery may have a tailored blue-and-white striped crib skirt with inverted pleats. To another deck, stitch a plain underskirt, which goes to the mattress platform first, below the main crib skirt, and can be removed when you lower the mattress as the infant grows. For the nautical motif, the second skirt may be solid red, or also a pattern of blue-on-white sailboats or stars.

Home

The way to Cease Air Leaking From the Sides and Greatest of an Overhead Garage Door

Stopping air escapes from the upper and sides of overhead doors are able to make your garage more comfortable also, if it is warmed, more energy-efficient. Garage door weatherstripping is cheap, easy to install and pays for itself over time in power savings. Sealing round the door also helps keep dirt, insects and tiny animals from entering the garage and possibly your home. You may pick up overhead garage door seals and installation supplies from the regional hardware or home improvement store.

Measure the top and either side of the overhead door opening with a tape measure and mark the center of the top outside trim with a pencil. Add the dimensions to obtain the total period of weather cutting required, then add 6 to 8 inches for overlap trimming.

Cut the weather seal into the total length needed — including the 6 to 8 inch excess — with a utility knife. Mark the center of the strip with pen.

Close the garage door and set up the stepladder at the center. Match the center mark of the weather seal with the center mark of the garage door trim.

Press the long edge of the seal against the garage door and hammer a nail through the short edge of the seal to fasten it into the trim.

Pull the weatherstripping taut–without stretching it–to a single side and fasten it with nails each 8 inches. Press the curved edge of the strip against the garage door as you move together.

Bend the door seal at a 90-degree angle when you get to the trim corner and nail it around 1 inch in the ends of their side and top trim bits.

Continue securing weather seal along the side trim, forcing the final nail around 1 inch in the bottom finish of the trim. Fold the excess seal at a 90-degree angle at the garage. Complete the seal installation along the remaining half of the top and down the other side of the door opening.

Trim the excess seal on each side of door seal so it fits neatly against the garage flooring, with the utility knife.